TT Map Case Large

Use the charging C360 Free Machining Brass ( Buttery Smooth ) head to charge the light and you're all set to keep on trekking.

Can be charged from work, home, laptop, USB Battery pack....

Specifications: 

• Length: 1.6" Diameter: .74" Weight: 27.8 Grams - No Battery 
• Battery weight 9 Grams
• Comes with extra o-rings
• LED Type: Cree XP-G2 S4 with a life span up to 50,000 hours. ( Newest & Brightest Emitter )
• Orange Peel Reflector for a smooth even beam
• Recharge Time is 30-100 minutes - depending on charge rate source
• The reflector is aluminum alloy.
• Flashlight body is made of C360 Free Machining Brass ( Buttery Smooth )
• Battery is 14250 Lithium Cell 280mAh
• The lens has been treated with a AR (Anti-Reflective) coating.
• Its proprietary circuit design features reverse polarity protection and runs off of one 14250 battery that provides 2 levels of brightness (Low / High).
  • Twist on for Low
  • Twist 1/2 turn more for High

Using a single 14250 battery we got the following results:

• Low mode, 15 lumens output for up to 9 hours

• High mode, 305 lumens output for up to 40 minutes

Includes Complete Kit:

1x Lithium Rechargable Battery
1x USB Charging Cable 
1x Charging SS Head With Charge indicator
1x PCL Light C360 Solid Brass Head & Body
4x Spare O-Rings

The Flat Gate Clip can be used to keep your everyday carry gear organized and ready for rapid deployment. The Flat Gate Clip is Water Jet cut and is truly made to last and can be used to carry any small preppers paraphernalia you may have.

Specifications:

       Small 20 mm x 9.25mm x 3mm ( 3.2 Grams )
       Medium 26mm x 12mm x 3mm ( 5.1 Grams )
       Large 33mm x 15mm x 4 mm ( 7 Grams )

• Made from 300 series stainless steel

IMPORTANT : This is not a life safety device.

Use the charging C360 Free Machining Brass ( Buttery Smooth ) head to charge the light and you're all set to keep on trekking.

Can be charged from work, home, laptop, USB Battery pack....

Specifications: 

• Length: 1.29" Diameter: .52" Weight: 9.9 Grams 
• Battery weight 3.4 Grams
• Comes with extra o-rings
• LED Type: Cree XP-G2 S4 with a life span up to 50,000 hours. ( Newest & Brightest Emitter )
• Orange Peel Reflector for a smooth even beam
• Recharge Time is 35-55 minutes 
• The reflector is aluminum alloy.
• Flashlight body is made of C360 Free Machining Brass ( Buttery Smooth )
• Battery is 10180 Lithium Cell 70mAh
• The lens has been treated with a AR (Anti-Reflective) coating.
• Its proprietary circuit design features reverse polarity protection and runs off of one 10180 battery that provides 2 levels of brightness (Low / High).
  • Twist on for Low
  • Twist 1/2 turn more for High

Using a single 10180 battery we got the following results:

• Low mode, 12 lumens output for up to 6 hours

• High mode, 145 lumens output for up to 25 minutes

Includes Complete Kit:

1x Lithium Rechargable Battery
1x USB Charging Cable 
1x Charging SS Head With Charge indicator
1x Peanut Light C360 Solid Brass Head & Body
5x Spare O-Rings

Proudly U.S.A Made!

When Uncle Sam requested a small pocket pry bar for technicians to open ordinance crates in the field, this was offered as the solution. The Widgy Pry Bar is made to fill the high demand for a customizable widgy bar which you can sharpen into your own EDC tool. These compact bars are heat treated D-9 steel and provide a common sense solution to broken knife blades and bent screw driver shafts. These are first run extras from government order.

EOD Robotics developed this compact breaching tool with input from Bomb Techs, SWAT Operators and Patrol Officers. All these folks need a tool for prying, cutting, pounding, and with extra versatility for shutting off gas valves during emergencies. 

Specifications:

• Made from 1045 high carbon steel and fully heat treated to a Rockwell hardness of over 45.
• The EOD Robotics Breacher Bar & CERT Bar come ready to go as a pry bar or lever. Ideal for opening crates and even punching through steel drums etc. The coffin corner back edge lends itself to a hammer nicely.
• The 2 inner holes in the handle can be for paracord or solid slabs or whatever you like. The hole towards the top of the blade and the one on the end are good for lashing it onto a shaft, tree branch etc. The end hole is geared for hanging it up or for attaching a lanyard so you do not lose it in that pit or in the water.
• The top edge can be hammered on as can the back end. And then you can use your imagination to do other things with it. (Makes a good wood chisel too!).
• Bars do not come with cord wrapped handles. You will receive the metal bar. The rest is up to you.
• Not pretty, but pretty handy. These were bulk packed for shipment to the military so they may have some rub marks where they have rubbed together in transit.
• Made in USA

Here's What Our Over-Protective Legal Department Has To Say:
Although the EOD Breacher Tool was developed and designed to enter the real world of urban combat, and with a little work with a file, belt sander, grinder, stone or a rock to it could be sharpened and converted to a Deadly stabbing or slashing instrument we can't recommend it. Likewise, the flat on the handle end should not be used as a skull or rib crusher or for performing other blunt trauma. Sorry these are not returnable. Be safe, and don't play with matches or run with scissors.