Ka-Bar Ice Scraper

385 Lumens!!! New even flow beam

Glow O-ring Around The Reflector ( easy to find in the dark )

Black Powder Coat Pocket Rotating Pocket Clip

The light is straightforward to use and has friendly ergonomics. The Maratac AAAx2 Extreme features an advance Cree XP-G2(R5) LED for greater brightness and efficiency.

•  Medium 45 Lumens / Low 5 lumens / High 385 lumens  mode brightness control (Simple 3 mode switching)
• Operation:
  • Press and click the back thumb switch to turn on the light into Medium mode. Lightly press again for Low mode and once more for High. Press and click anytime to turn the light off.

SPECIFICATIONS:

• 22.8 grams or .8 oz (without battery)
• 5.0" O.A.L. x .58" inch width
• Type 3 Military Grade Anodizing ( Matte Finish )
• Utilizes 2 Standard AAA Batteries ( 1.2-1.7 Volts each )
• Standard Modes ( Pressing Tail Cap Through Modes )
• • Medium ( 6 Hours )
  • Low ( 90 hours )
  • High ( 1.65 hours )

The reflector glows after the light turns off so it's easy to find in the night.

Specifications:

• Length: 2.65" 
• Diameter: .57" 
• Stainless Steel Pocket Clip ( Easy to clip onto a hat, MOLLE gear or shirt pocket )
• Glow In the Dark Built In reflector ( Easy to find in the dark )
• LED Type: Cree G2 Emitter ( High Output ) with a life span up to 50,000 hours. 
• Flashlight body is machined of solid billet C360 Free Machining Brass ( Buttery Smooth )
• Stainless Steel ring around the dome lens for added durability
• The dome lens has been treated with an AR (Anti-Reflective) coating.
• Proprietary circuit design features reverse polarity protection and runs off of one AAA battery that provides 3 levels of brightness ( Medium / Low/ High ).

Using a single Duracell AAA battery we got the following results:

• Low Mode, 5 lumen output for up to 60 Hours ( Diffused Light )
• Medium Mode, 48 lumen output for up to 4 Hours
• High Mode, 160 lumen output for up to 75 Minutes

Proudly U.S.A Made!

When Uncle Sam requested a small pocket pry bar for technicians to open ordinance crates in the field, this was offered as the solution. The Widgy Pry Bar is made to fill the high demand for a customizable widgy bar which you can sharpen into your own EDC tool. These compact bars are heat treated D-9 steel and provide a common sense solution to broken knife blades and bent screw driver shafts. These are first run extras from government order.

Use the charging C360 Free Machining Brass ( Buttery Smooth ) head to charge the light and you're all set to keep on trekking.

Can be charged from work, home, laptop, USB Battery pack....

Specifications: 

• Length: 1.29" Diameter: .52" Weight: 9.9 Grams 
• Battery weight 3.4 Grams
• Comes with extra o-rings
• LED Type: Cree XP-G2 S4 with a life span up to 50,000 hours. ( Newest & Brightest Emitter )
• Orange Peel Reflector for a smooth even beam
• Recharge Time is 35-55 minutes 
• The reflector is aluminum alloy.
• Flashlight body is made of C360 Free Machining Brass ( Buttery Smooth )
• Battery is 10180 Lithium Cell 70mAh
• The lens has been treated with a AR (Anti-Reflective) coating.
• Its proprietary circuit design features reverse polarity protection and runs off of one 10180 battery that provides 2 levels of brightness (Low / High).
  • Twist on for Low
  • Twist 1/2 turn more for High

Using a single 10180 battery we got the following results:

• Low mode, 12 lumens output for up to 6 hours

• High mode, 145 lumens output for up to 25 minutes

Includes Complete Kit:

1x Lithium Rechargable Battery
1x USB Charging Cable 
1x Charging SS Head With Charge indicator
1x Peanut Light C360 Solid Brass Head & Body
5x Spare O-Rings

EOD Robotics developed this compact breaching tool with input from Bomb Techs, SWAT Operators and Patrol Officers. All these folks need a tool for prying, cutting and pounding, and here's the answer.

Specifications:

• Made from 1045 high carbon steel and fully heat treated to a Rockwell hardness of over 45.
• The EOD Robotics Breacher Bar & CERT Bar come ready to go as a pry bar or lever. Ideal for opening crates and even punching through steel drums etc. The coffin corner back edge lends itself to a hammer nicely.
• The 2 inner holes in the handle can be for paracord or solid slabs or whatever you like. The hole towards the top of the blade and the one on the end are good for lashing it onto a shaft, tree branch etc. The end hole is geared for hanging it up or for attaching a lanyard so you do not lose it in that pit or in the water.
• The top edge can be hammered on as can the back end. And then you can use your imagination to do other things with it. (Makes a good wood chisel too!).
• Bars do not come with cord wrapped handles. You will receive the metal bar. The rest is up to you.
• Not pretty, but pretty handy. These were bulk packed for shipment to the military so they may have some rub marks where they have rubbed together in transit.
• Made in USA

Here's What Our Over-Protective Legal Department Has To Say:
Although the EOD Breacher Tool was developed and designed to enter the real world of urban combat, and with a little work with a file, belt sander, grinder, stone or a rock to it could be sharpened and converted to a Deadly stabbing or slashing instrument we can't recommend it. Likewise, the flat on the handle end should not be used as a skull or rib crusher or for performing other blunt trauma. Sorry these are not returnable. Be safe, and don't play with matches or run with scissors.